I have been trying to compile megahal for a few hours now and i dont seem to be getting anywhere. Has anyone had success with this?
http://megahal.alioth.debian.org/
I keep getting an error that says :
inlined from ‘load_personality.constprop’ at megahal.c:3283:8,
inlined from ‘change_personality.constprop’ at megahal.c:3332:5:
/usr/include/x86_64-linux-gnu/bits/stdio2.h:293:2: warning: call to ‘__fread_chk_warn’ declared with attribute warning: fread called with bigger size * nmemb than length of destination buffer
return __fread_chk_warn (__ptr, __bos0 (__ptr), __size, __n, __stream);
^
cc1: some warnings being treated as errors
error: command 'x86_64-linux-gnu-gcc' failed with exit status 1
Makefile:44: recipe for target 'pythonmodule' failed
make: *** [pythonmodule] Error 1
I have installed python via sudo apt-get and i have been over every thread that talks about "'x86_64-linux-gnu-gcc' but I have found no solution
You are getting these errors just because you don't have the python development headers installed. You can install it using following command
sudo apt-get install python-dev ( for python 2.x )
sudo apt-get install python3-dev ( for python 3 )
you need the python developer module "python-dev".this will help you
error: command 'gcc' failed with exit status 1 while installing eventlet
after upgrading to vivid 15.04 on ubuntu i couldn't compile the module anymore so i tried something else. Since in the main folder there is a directory named Megahal with a Makefile in it, i tried to compile from there. First you need to go to that directory.
cd /home/user/Downloads/megahal-9.1.1/Megahal/
you need to go where you unzipped the archive and there you can read the README file and start compiling.
perl Makefile.PL
i copied the missing files i was able to find to that folder and from there
make
make test
but this didn't work for me and afther that
make install
i had to do
sudo make install
and that is all. unfortunately for me i have a problem with perl i think.
I keep getting this error from the module "PL_thr_key" after i load it to the eggdrop. The eggdrop works normally except for the module. No module, no AI and no fun :(
Related
I am trying to install 'pocketsphinx' module in python which requires swig.exe. After a lot of searching I followed the steps mentioned in the swig site(http://www.swig.org/Doc3.0/Windows.html#Windows_swig_exe) to build an exe. But I am stuck at the last 2 steps.
When './autogen.sh' is executed, I get the following error message although the file 'aclocal' is present in the '/mingw/bin' directory.
vinay#DESKTOP-7LB2J5M /usr/src/swig
$ ./autogen.sh
+ test -d Tools/config
+ aclocal -I Tools/config
./autogen.sh: /mingw/bin/aclocal: No such file or directory
I renamed c:\MinGW\msys\1.0\etc\fstab.sample to c:\MinGW\msys\1.0\etc\fstab and also installed automake, libtool, autoconf, aclocal, autoheader dependencies from MinGW installation manager. What am I missing?
I am not familiar with MinGw or unix commands.
I have protobuf compiler version 3.0 and need to install grpc and grpc python plugin. Following the tutorial, I added deb http://http.debian.net/debian jessie-backports main to my sources.list file and did sudo apt-get update and sudo apt-get install libgrpc-dev which returned
Package libgrpc-dev is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source
E: Package 'libgrpc-dev' has no installation candidate
So, I decided to compile it from source as mentioned in INSTALL notes and did:
$ git clone https://github.com/grpc/grpc.git
$ cd grpc
$ git submodule update --init
$ make
$ [sudo] make install
However, on the make step, I get
[MAKE] Generating cache.mk
make: Circular /home/vagrant/grpc2/grpc/libs/opt/libboringssl.a <- /home/vagrant/grpc2/grpc/libs/opt/libboringssl.a dependency dropped.
[C] Compiling third_party/boringssl/crypto/bio/connect.c
third_party/boringssl/crypto/bio/connect.c: In function 'split_host_and_port':
third_party/boringssl/crypto/bio/connect.c:127:17: error: declaration of 'close' shadows a global declaration [-Werror=shadow]
cc1: all warnings being treated as errors
make: *** [/home/vagrant/grpc2/grpc/objs/opt/third_party/boringssl/crypto/bio/connect.o] Error 1
On switching to the release-0_11 branch, running make results in
[HOSTCXX] Compiling src/compiler/csharp_generator.cc
src/compiler/csharp_generator.cc:47:43: error: 'google::protobuf::compiler::csharp::GetUmbrellaClassName' has not been declared
src/compiler/csharp_generator.cc: In function 'void grpc_csharp_generator::{anonymous}::GenerateServiceDescriptorProperty(grpc::protobuf::io::Printer*, const ServiceDescriptor*)':
src/compiler/csharp_generator.cc:237:62: error: 'GetUmbrellaClassName' was not declared in this scope
make: *** [/home/vagrant/grpc2/grpc/objs/opt/src/compiler/csharp_generator.o] Error 1
I can't figure out how to install this. Any help would be appreciated.
For me the issue got fixed after i made change in the file as:
diff --git a/src/compiler/csharp_generator.cc
b/src/compiler/csharp_generator.cc
index 7b497df..5a8746d 100644
--- a/src/compiler/csharp_generator.cc
+++ b/src/compiler/csharp_generator.cc
## -44,7 +44,7 ##
using google::protobuf::compiler::csharp::GetFileNamespace;
using google::protobuf::compiler::csharp::GetClassName;
-using google::protobuf::compiler::csharp::GetUmbrellaClassName;
+using google::protobuf::compiler::csharp::GetReflectionClassName;
using grpc::protobuf::FileDescriptor;
using grpc::protobuf::Descriptor;
using grpc::protobuf::ServiceDescriptor;
## -234,7 +234,7 ## void GenerateServiceDescriptorProperty(Printer* out, const ServiceDescriptor *se
out->Print("public static global::Google.Protobuf.Reflection.ServiceDescriptor Descriptor\n");
out->Print("{\n");
out->Print(" get { return $umbrella$.Descriptor.Services[$index$]; }\n",
- "umbrella", GetUmbrellaClassName(service->file()), "index",
+ "umbrella", GetReflectionClassName(service->file()), "index",
index.str());
out->Print("}\n");
out->Print("\n");
More specifically, please open the file src/compiler/csharp_generator.cc and replace all references of GetUmbrellaClassName by GetReflectionClassName
Working backwards:
for release-0_11: it looks like you're trying to compile against the most recent protobuf. Since we're both in development right now there's occasional breakage - but grpc does track the version of protobuf it's tested against in third_party/protobuf. Try checking out and installing that version. I filed https://github.com/grpc/grpc/issues/4697 to update to the latest protobuf 3.0 version.
for master from github: which compiler and OS are you using? I recently checked in the boringssl integration work, so it's fresh, and not nearly as battle-tested. I'd like to get it battle-tested. That said, if you do a 'make EMBED_OPENSSL=false' then things should work out for you.
for the debian package problem: I'm not sure what's going on. I'm happy to try and spin up a VM with your OS and repro if you can let me know which OS it is.
MAC OSX 10.9, Python 3.5, sip-4.17, PyQt-gpl-5.5.1, Qt5.5.1
Hi,
trying to build PyQt on my system I did the following steps:
download/install Qt5.5.1 libraries
download/unpack SIP
download/unpack PyQt
install SIP:
python3 configure.py -d /Library/Python/3.5/site-packages --arch x86_64
make
sudo make install
tried to install PyQt:
python3 configure.py -d /Library/Python/3.5/site-packages
--qmake /.../Qt5.5.1/5.5/clang_64/bin/qmake
Configuration stopped with:
/Users/werner/OpenSource/PyQt/sip/QtPositioning/qgeolocation.sip:28:10:
fatal >error: 'qgeolocation.h' file not found
#include <qgeolocation.h>
^
1 error generated.
make[1]: *** [sipQtPositioningcmodule.o] Error 1
make: *** [sub-QtPositioning-make_first-ordered] Error 2
I tried to finish installation doing
make
sudo make install
anyway. But the installation doesn't seem to be complete (e.g. uic, pyuic5 are missing). Here is what my installation directory looks like:
>ls /Library/Python/3.5/site-packages/PyQt5
QtBluetooth.so QtSensors.so
QtCore.so QtSerialPort.so
QtDBus.so QtSql.so
QtDesigner.so QtSvg.so
QtGui.so QtTest.so
QtHelp.so QtWebKit.so
QtMacExtras.so QtWebKitWidgets.so
QtMultimedia.so QtWidgets.so
QtMultimediaWidgets.so QtXml.so
QtNetwork.so QtXmlPatterns.so
QtOpenGL.so _QOpenGLFunctions_2_0.so
QtPrintSupport.so _QOpenGLFunctions_2_1.so
QtQml.so _QOpenGLFunctions_4_1_Core.so
QtQuick.so
I couldn't find any useful information when searching for other discussions, so I hope someone can give me a hint on what I'm (maybe stupidly) doing wrong. Thank you for taking the time to read this.
If you don't need this module, the better way to solve that is disabling it on configure.
python configure.py --disable=QtPositioning
Just yesterday, I also met such a problem. And this is what I do to solve it:
Create a header file qgeolocation.h in /PyQt-gpl-5.5.1/QtPositioning, and copy the content into it from this website. Then I go sudo make and sudo make install successfully.
Though I do not know whether it is right to solve this problem, fortunately, I installed the PyQt and entered eric6. Hope you make successfully, too.
Adding the location.h header file for me on OSX 10.11.1.
I had the problem in both PyQt-gpl-5.5.1 and PyQt-gpl-5.5.2, but after adding the
file, was able to build.
The way of creating a qgeolocation.h in /PyQt-gpl-5.5.1/QtPositioning worked for me. The QtPositioning.so was created.
You can also take the header file from your qt source folder (you have installed the source files together with binaries, right?), it is located here:
/Src/qtlocation/src/positioning/qgeolocation.h
and then just copy it into:
/PyQt-gpl-X.X.X/QtPositioning/qgeolocation.h
as follows. It should solve the problem in 99.9% cases.
Environment: Win 7, Python 3.4, Sublime Text 2
I am trying to use fontforge as in following example, by importing fontforge in *.py:
import fontforge
font = fontforge.open('blank.sfd')
...
However, I haven't found any help for win 7 on where (or which subset) to include fontforge binary in my project to make it work. Any ideas, please? Thanks
Edit:
I was trying to build it with pyextension in win 7 as described here:
http://fontforge.org/source-build.html#MS
via cygwin it fails on executing
./configure --enable-pyextension
throwing
checking for gcc
result: no
checking for cc
result: no
checking for cl.exe
result: no
error: in `/cygdrive/c/fontforge':
no acceptable C compiler found in $PATH
Edit 2:
By installing C compiler I've managed to ./configure it but my attempts have failed on executing make install command. I got following error, preceding another countless lines:
Makefile:91: recipe for target '../libfontforge.la' failed
make[1]: *** [../libfontforge.la] Error 1
make[1]: Leaving directory '/cygdrive/c/fontforge/fontforge'
Makefile:28: recipe for target 'fontforge' failed
make: *** [fontforge] Error 2
Install fontforge for windows, then search your install for a fontforge-console.bat, and double-click it. From there you have a python environment that includes fontforge via the command:
ffpython
e.g.:
ffpython yourPythonFontForgeScript.py
You may need to cd to whatever directory has your python script before running that command, or otherwise make sure that the script is in your %PATH%.
I am trying to install "pretty damn quick", an analysis tool for Layered Queing networks.
However there seems to be a lot wrong with my system, and switching to Linux is not an option.
Here is what i tried to get the PDQ running:
First try: Python
I installed python2.7 and downloaded the PDQ for python distribution (its in the tarball in the python dir) :
C:\pdq\pdq42\python>python setup.py install
running install
running build
running build_ext
building 'pdq' extension
error: Unable to find vcvarsall.bat
This error stems from the fact that i supposedly dont have a C-compiler. Even though typing g++ gives me:
C:\pdq\pdq42\python>g++ -v
Using built-in specs.
COLLECT_GCC=g++
COLLECT_LTO_WRAPPER=c:/rtools/gcc-4.6.3/bin/../libexec/gcc/i686-w64-mingw3
3/lto-wrapper.exe
Target: i686-w64-mingw32
...snipped...
This problem is somehow documented? So i tried going over to Perl. It said there that the compiler comes with Strawberry Perl. So I installed that. Dmake gave me a lot of trouble but in the end I managed to install it.
C:\pdq\pdq42\perl5>perl Makefile.PL
Writing Makefile for pdq
C:\pdq\pdq42\perl5>dmake
Skip blib\lib\pdq.pm (unchanged)
...snipped...
g++.exe: error: MVA_Approx.o: No such file or directory
g++.exe: error: MVA_Canon.o: No such file or directory
g++.exe: error: MVA_Solve.o: No such file or directory
g++.exe: error: PDQ_Build.o: No such file or directory
g++.exe: error: PDQ_Exact.o: No such file or directory
g++.exe: error: PDQ_Globals.o: No such file or directory
g++.exe: error: PDQ_Report.o: No such file or directory
g++.exe: error: PDQ_Utils.o: No such file or directory
dmake: Error code 129, while making 'blib\arch\auto\pdq\pdq.dll'
Gives me new errors, that i cannot fix, since i cannot google them.
As the last resort i try out installing R, since this should work according to the documentation.
install.packages("c:\pdq\pdq_6.0-1.tar.gz",repos=NULL,type="source")
Warning: invalid package 'c:/pdq/pdq_6.0-1.tar.gz'
Error: ERROR: no packages specified
Warning messages:
1: running command '"C:/Programme/R/R-3.0.1/bin/i386/R" CMD INSTALL -l "C:\Programme\R\R-3.0.1\library" "c:/pdq/pdq_6.0-1.tar.gz"' had status 1
2: In install.packages("c:\pdq\pdq_6.0-1.tar.gz", repos = NULL, type = "source") :
installation of package ‘c:/pdq/pdq_6.0-1.tar.gz’ had non-zero exit status
However in this case i don't even know where to start debugging this to get it going.
So I am seeking help from SO. My question is:
Where did I go wrong and what can I do to find additional information leading to identify the problem? I would really like to have PDQ installed.