I needed to write and read data with pyserial.
I'm sending the output I want with write command
and then want to check and read arrival of new data.
when I'm calling the read command it's also printing the data i have sent.
this is the code below:
#on one script:
while 1:
serial.write(str.encode("blabla111"))
bytesToRead = serial.inWaiting()
if bytesToRead is not 0:
print(serial.read(bytesToRead))
time.sleep(1)
#on second script:
while 1:
serial.write(str.encode("hello222"))
bytesToRead = serial.inWaiting()
if bytesToRead is not 0:
print(serial.read(bytesToRead))
time.sleep(1)
#print result on first script (excepting to get only :hello222)
blabla111hello222
What am I missing here?
I tried to use the flush command didn't help
Related
I am currently trying to use pyserial to read the values from my handheld tachometer, the specific model is the DT-2100.
I am using python 3 and my current code looks like this:
# Imports
import serial
import time
import io
# Coding section
# Setting Parameters
port = "COM3"
baud = 38400
data = []
info = 0
# Setting the port location, baudrate, and timeout value
ser = serial.Serial(port, baud, timeout=2)
# Ensuring that the port is open
if ser.isOpen():
print(ser.name + ' is open...')
# trying to read a single value from the display
#input("Ensure that the DT-2100 is turned on...")
info = ser.write(b'CSD')
ser.write(b'CSD')
info_real = ser.readlines()
print()
print("The current value on the screen is: ", info)
print()
print("The real value on the screen is: ", info_real)
This is what I get back after running the code:
COM3 is open...
The current value on the screen is: 3
The real value on the screen is: []
Process finished with exit code 0
The main issue is that I should be getting the value that is displayed by the tachometer, which for this test was 0, but between my two attempted methods I got 3 and nothing.
Any help is greatly appreciated.
The zip file you linked to contained an xls file which seemed to detail all the commands.
All the commands seem to be wrapped in: <STX> cmd <CR>, so you are missing those.
The CSD command would need to be like this: ser.write(b'\x02CSD\r')
Similarly the reply is also wrapped in the same way and you would need to remove those bytes and interpret the rest.
I am trying to make a program which constantly reads data being sent from device using serial port to computer. In addition to this whenever I enter something it is sent to device.(My main aim is to make a serial terminal emulator).
I wrote following program but it waits for any input and does not constantly read data and display on screen sent by device as thought:
ser1 = serial.Serial(com_name_to_use, auto_baud, timeout=0, write_timeout=0)
while True:
try:
# Writing Section
inp_str1 = input() # + "\n"
str1 = inp_str1.encode(encoding="ascii")
ser1.write(str1)
time.sleep(0.03)
# Reading Section
bf = ser1.readline()
print(str(bf, encoding="utf-8"), end="")
except Exception as err1:
pass
Kindly, tell how to fix it.
I have pexpect working, but I am having problems printing the output back from it. In my test script below, it creates the ssh connection, and then sends a sudo su -, then my password, and then sends a line that would require sudo access to do (I have also added p.interact() a few times to make sure it is at root). The problem I am having, is with returning the output of the commands I run. In the end I am wanting to run some top commands, and some du -h, and other(much more complex) space commands. But currently when it tries to print p.before, I get:
Traceback (most recent call last):
File "./ssh.py", line 37, in <module>
print p.before()
TypeError: 'str' object is not callable
Here is the script I am working from(edited to remove my pass and such)
#!/usr/bin/env python
import pexpect
import struct, fcntl, os, sys, signal
def sigwinch_passthrough (sig, data):
# Check for buggy platforms (see pexpect.setwinsize()).
if 'TIOCGWINSZ' in dir(termios):
TIOCGWINSZ = termios.TIOCGWINSZ
else:
TIOCGWINSZ = 1074295912 # assume
s = struct.pack ("HHHH", 0, 0, 0, 0)
a = struct.unpack ('HHHH', fcntl.ioctl(sys.stdout.fileno(), TIOCGWINSZ , s))
global global_pexpect_instance
global_pexpect_instance.setwinsize(a[0],a[1])
ssh_newkey = 'Are you sure you want to continue connecting'
p=pexpect.spawn('ssh user#localhost')
i=p.expect([ssh_newkey,'password:',pexpect.EOF,pexpect.TIMEOUT],1)
if i==0:
print "I say yes"
p.sendline('yes')
i=p.expect([ssh_newkey,'password:',pexpect.EOF])
if i==1:
print "I give password",
p.sendline("mypassword")
elif i==2:
print "I either got key or connection timeout"
pass
elif i==3: #timeout
pass
global global_pexpect_instance
global_pexpect_instance = p
p.sendline("sudo su -")
p.sendline("mypasswd")
p.sendline("mkdir /home/user/test")
print p.before
I am working off of this link: http://linux.byexamples.com/archives/346/python-how-to-access-ssh-with-pexpect/
Any help is much appreciated.
EDIT: As Armin Rigo pointed out below. I was calling to p.before as a function like p.before(). Stupid mistake on my part, as this explains why I was getting this error today, and not yesterday when I was trying this. After making that change to my script, and modifying the command being sent, print p.before, and no output is returned. Any other ways to return output from a sendline() command?
Use logfile, that logfile is store all output in terminal.use that example code:-
child = pexpect.spawn("ssh user#localhost")
child.logfile = open("/tmp/mylog", "w")
child.expect(".*assword:")
child.send("guest\r")
child.expect(".*\$ ")
child.sendline("python -V\r")
open the log file and see everything in terminals event
To fetch the complete output after sendline use child.read()
e.g.
cmd_resp = pexpect.spawnu(cmd) # for execution of the command
str_to_search = 'Please Enter The Password'
cmd_resp.sendline('yes') # for sending the input 'yes'
resp = cmd_resp.expect([str_to_search, 'password:', EOF], timeout=30) # fetch the output status
if resp == 1:
cmd_resp.sendline(password)
resp = cmd_resp.expect([str_to_search, 'outputString:', EOF], timeout=30)
print(cmd_resp.read()) # to fetch the complete output log
p.before is a string - not a function. To see the output you have to write
print p.before.
Hope this might help you
I'm using Python/Pexpect to spawn an SSH session to multiple routers. The code will work for one router but then the output of session.before will get out of sync with some routers so that it will return the output from a previous sendline. This seems particularly the case when sending a blank line (sendline()). Anyone got any ideas? Any insight would be really appreciated.
Below is a sample of what I'm seeing:
ssh_session.sendline('sh version')
while (iresult==2):
iresult = ssh_session.expect(['>','#','--More--'],timeout=SESSION_TIMEOUT)
debug_print("execute_1 " + str(iresult))
debug_print("execute_bef " + ssh_session.before)
debug_print("execute_af " + ssh_session.after)
thisoutput = ssh_session.before
output += thisoutput
if(iresult==2):
debug_print("exec MORE")
ssh_session.send(" ")
else:
debug_print("exec: end loop")
for cmd in config_commands:
debug_print("------------------------------------------------\n")
debug_print ("running command " + cmd.strip() + "\n")
iresult=2
ssh_session.sendline(cmd.strip())
while (iresult==2):
iresult = ssh_session.expect([prompt+">",prompt+"#"," --More-- "],timeout=SESSION_TIMEOUT)
thisoutput = ssh_session.before
debug_print("execute_1 " + str(iresult))
debug_print("execute_af " + ssh_session.after)
debug_print("execute_bef " + thisoutput)
thisoutput = ssh_session.before
output += thisoutput
if(iresult==2):
debug_print("exec MORE")
ssh_session.send(" ")
else:
debug_print("exec: end loop")
I get this:
logged in
exec: sh version
execute_1 1
execute_bef
R9
execute_af #
exec: end loop
------------------------------------------------
running command config t
execute_1 1
execute_af #
execute_bef sh version
Cisco IOS Software, 1841 Software (C1841-IPBASEK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport...
I've run into this before with pexpect (and I'm trying to remember how I worked around it).
You can re-synchronize with the terminal session by sending a return and then expecting for the prompt in a loop. When the expect times out then you know that you are synchronized.
The root cause is probably that you are either:
Calling send without a match expect (because you don't care about the output)
Running a command that produces output but expecting for a pattern in the middle of that output and then not to next prompt that is at end of the output. One way to deal with this is to change your expect pattern to "(.+)PROMPT" - this will expect until the next prompt and capture all the output of the command sent (which you can parse in the next step).
I faced a similar problem. I tried waiting for the command to be printed on the screen and the sending enter.
I you want to execute say command 'cmd', then you do:
session.send(cmd)
index = session.expect([cmd, pexpect.TIMEOUT], 1)
session.send('\n')
index = session.expect([whatever you expect])
Worked for me.
I'm not sure this is the root of your problem, but it may be worth a try.
Something I've run into is that when you spawn a session that starts with or lands you in a shell, you have to deal with quirks of the TERM type (vt220, color-xterm, etc.). You will see characters used to move the cursor or change colors. The problem is almost guaranteed to show up with the prompt; the string you are looking for to identify the prompt appears twice because of how color changes are handled (the prompt is sent, then codes to backspace, change the color, then the prompt is sent again... but expect sees both instances of the prompt).
Here's something that handles this, guaranteed to be ugly, hacky, not very Pythonic, and functional:
import pexpect
# wait_for_prompt: handle terminal prompt craziness
# returns either the pexpect.before contents that occurred before the
# first sighting of the prompt, or returns False if we had a timeout
#
def wait_for_prompt(session, wait_for_this, wait_timeout=30):
status = session.expect([wait_for_this, pexpect.TIMEOUT, pexpect.EOF], timeout=wait_timeout)
if status != 0:
print 'ERROR : timeout waiting for "' + wait_for_this + '"'
return False
before = session.before # this is what we will want to return
# now look for and handle any additional sightings of the prompt
while True:
try:
session.expect(wait_for_this, timeout=0.1)
except:
# we expect a timeout here. All is normal. Move along, Citizen.
break # get out of the while loop
return before
s = pexpect.spawn('ssh me#myserver.local')
s.expect('password') # yes, we assume that the SSH key is already there
# and that we will successfully connect. I'm bad.
s.sendline('mypasswordisverysecure') # Also assuming the right password
prompt = 'me$'
wait_for_prompt(s, prompt)
s.sendline('df -h') # how full are my disks?
results = wait_for_prompt(s, prompt)
if results:
print results
sys.exit(0)
else:
print 'Misery. You lose.'
sys.exit(1)
I know this is an old thread, but I didn't find much about this online and I just got through making my own quick-and-dirty workaround for this. I'm also using pexpect to run through a list of network devices and record statistics and so forth, and my pexpect.spawn.before will also get out of sync sometimes. This happens very often on the faster, more modern devices for some reason.
My solution was to write an empty carriage return between each command, and check the len() of the .before variable. If it's too small, it means it only captured the prompt, which means it must be at least one command behind the actual ssh session. If that's the case, the program sends another empty line to move the actual data that I want into the .before variable:
def new_line(this, iteration):
if iteration > 4:
return data
else:
iteration+=1
this.expect(":")
this.sendline(" \r")
data = this.before
if len(data) < 50:
# The numer 50 was chosen because it should be longer than just the hostname and prompt of the device, but shorter than any actual output
data = new_line(this, iteration)
return data
def login(hostname):
this = pexpect.spawn("ssh %s" % hostname)
stop = this.expect([pexpect.TIMEOUT,pexpect.EOF,":"], timeout=20)
if stop == 2:
try:
this.sendline("\r")
this.expect(":")
this.sendline("show version\r")
version = new_line(this,0)
this.expect(":")
this.sendline("quit\r")
return version
except:
print 'failed to execute commands'
this.kill(0)
else:
print 'failed to login'
this.kill(0)
I accomplish this by a recursive command that will call itself until the .before variable finally captures the command's output, or until it calls itself 5 times, in which case it simply gives up.
I have an embedded linux device and here's what I would like to do using python:
Get the device console over serial port. I can do it like this:
>>> ser = serial.Serial('/dev/ttyUSB-17', 115200, timeout=1)
Now I want to run a tail command on the embedded device command line, like this:
# tail -f /var/log/messages
and capture the o/p and display on my python >>> console.
How do I do that ?
Just open the file inside python and keep readign from it. If needed be, in another thread:
>>> ser = serial.Serial('/dev/ttyUSB-17', 115200, timeout=1)
>>> output = open("/var/log/messages", "rb")
And inside any program loop, just do:
data = output.read()
print(data)
If you want it to just go printing on the console as you keep doing other stuff, type
in something like:
from time import sleep
from threading import Thread
class Display(Thread):
def run(self):
while True:
data = self.output.read()
if data: print(data)
sleep(1)
t = Display()
t.output = output
t.start()
very first you need to get log-in into the device.
then you can run the specified command on that device.
note:command which you are going to run must be supported by that device.
Now after opening a serial port using open() you need to find the login prompt using Read() and then write the username using write(), same thing repeat for password.
once you have logged-in you can now run the commands you needed to execute