I am using a kunbus RevPi connect + to control a pump with a USB serial converter. To control it, I need to send ASCII command so I try to use the Pyserial library.
import serial
import time
ser = serial.Serial('/dev/ttyUSB2', baudrate = 9600, bytesize=8, parity='N', stopbits=1, timeout=1)
print (ser.portstr)
ser.write(b"1H[CR]")
I haven't error message but the pump doesn' start.
Can you help me please?
thanks in advance.
I'm trying to read from a serial device using future technology devices international ltd bridge(i2c/spi/uart/fifo).
The device is designed to only send data. It has been tested in a Windows environment and is working correctly.
I'm using Ubuntu 16.04.2 LTS with the pyserial python module as follow:
import serial
ser = serial.Serial(
port ='/dev/ttyUSB0',
baudrate=38400,
parity=serial.PARITY_NONE,
stopbits=serial.STOPBITS_ONE,
bytesize=serial.EIGHTBITS,
timeout=5
)
buff = ser.read(128)
print buff
ser.close()
When I run the script I can't read anything from the device. Do you have any idea or suggestion?
Thank you very much for the help.
import time
import serial
# configure the serial connections (the parameters differs on the device you are connecting to)
ser = serial.Serial(
port='/dev/ttyS0',
#port='/dev/ttyACM0',
baudrate=115200,
parity=serial.PARITY_ODD,
#stopbits=serial.STOPBITS_TWO,
#bytesize=serial.SEVENBITS
)
ser.isOpen() # returns true
time.sleep(1);
ser.write("some_command \n")
ser.close()
I have a embedded board. It has a serial port which is connected to my computer. I am running above script to access this serial port and run some board specific commands.
My problem
I open my serial port (using minicom in linux) separately and then run above script, It works. If I don't open serial port separately, Script doesn't work.
try
ser.write("some_command \n".encode())
alternatively try
ser.write(bytes(b"some_command \n"))
I have a rectifier outputting voltage and amperage information every 3 seconds. I installed python 2.7 and pySerial without a hitch. I am trying to get the following code to read data being sent at baud 2400, 7 data bits, even parity, and one stop bit. Other RS232 programs get it without a hitch. When I start the program from cmd I get a blinking underscore. What am I doing wrong?
import time
import serial
ser = serial.Serial(
port='COM3',
baudrate=2400,
parity=serial.PARITY_NONE,
stopbits=serial.STOPBITS_ONE,
bytesize=serial.SEVENBITS
)
while True:
message = ser.readline()
print(message)
time.sleep(3)
I have two Xbee Pro 900's, each attached to a Raspberry Pi. Both are updated to version 1061 and are set to API Enable with escapes. They also have the same Modem VID of 7FFF. Both Pi's have PySerial and the python-xbee library installed.
Xbee 1(Receiver) has a serial number of 0013A200409A1BB8
Xbee 2(Sender) has a serial number of 0013A200709A1BE9
I've included my code below, which is just sample code I've found online. My issue is that I'm not receiving anything on the appropriate Xbee. I have absolutely no idea what is wrong, I've triple checked the destination address, and both of the Xbee's configuration settings.
Xbee 2 Code(Sender):
#! /usr/bin/python
import time
from xbee import XBee
import serial
PORT = '/dev/ttyUSB0'
BAUD_RATE = 9600
# Open serial port
ser = serial.Serial(PORT, BAUD_RATE)
# Create API object
xbee = XBee(ser,escaped=True)
import pprint
pprint.pprint(xbee.api_commands)
DEST_ADDR_LONG = "\x00\x13\xA2\x00\x40\x9A\x1B\xB8"
# Continuously read and print packets
while True:
try:
print "send data"
xbee.tx_long_addr(frame='0x1', dest_addr=DEST_ADDR_LONG, data='AB')
time.sleep(1)
except KeyboardInterrupt:
break
ser.close()
Xbee 1 Code(Receiver):
#! /usr/bin/python
from xbee import XBee
import serial
PORT = '/dev/ttyUSB0'
BAUD_RATE = 9600
# Open serial port
ser = serial.Serial(PORT, BAUD_RATE)
# Create API object
xbee = XBee(ser,escaped=True)
# Continuously read and print packets
while True:
try:
print "waiting"
response = xbee.wait_read_frame()
print response
except KeyboardInterrupt:
break
ser.close()
When both programs are running, the Tx light on the sending Xbee blinks, but I receive nothing on the receiving Xbee. Is there something I'm missing? Thanks for your time!
Are you using XBee or XBeePro? I had the same problem and this post helped me a lot.
Try to modify the Receiver Code the following way:
import config
import serial
import time
from xbee import ZigBee
def toHex(s):
lst = []
for ch in s:
hv = hex(ord(ch)).replace('0x', '')
if len(hv) == 1:
hv = '0'+hv
hv = '0x' + hv
lst.append(hv)
def decodeReceivedFrame(data):
source_addr_long = toHex(data['source_addr_long'])
source_addr = toHex(data['source_addr'])
id = data['id']
samples = data['samples']
options = toHex(data['options'])
return [source_addr_long, source_addr, id, samples]
PORT = '/dev/ttyUSB0'
BAUD_RATE = 9600
# Open serial port
ser = serial.Serial(PORT, BAUD_RATE)
zb = ZigBee(ser, escaped = True)
while True:
try:
data = zb.wait_read_frame()
decodedData = decodeReceivedFrame(data)
print decodedData
except KeyboardInterrupt:
break
In my case the code above outputs the following:
[['0x00', '0x13', '0xa2', '0x00', '0x40', '0x9b', '0xaf', '0x4e'], ['0x68', '0x3f'], 'rx_io_data_long_addr', [{'adc-0': 524}]]
Here I shared configuration settings for Controller Node (compatible with X-CTU)
Are you sure the XBee modules are in escaped API mode (ATAP=2)? And 9600 baud?
Can you enable a mode in python-xbee to dump all characters in and out?
Have you confirmed the serial wiring is correct? (I see you're using USB, so that's not an issue.)
If you don't have hardware flow control hooked up, make sure the XBee modules have ATD6=0 and ATD7=0 set (disable RTS and CTS) and that python-xbee isn't expecting handshaking.
If you do have hardware flow control configured on the XBee, make sure you've told python-xbee to use it.
Can you use minicom or another serial terminal on the RaspPi to confirm that serial is working? Use minicom on the receiving end to see if you're getting anything at all?
Can you try sending and receiving with the radios connected to a PC instead of the Pi? Sending from the PC to the Pi, or vice-versa?