I have been trying for a day to install Pandas_ta on my raspberry py with little succes. I first made a Python script on my PC and then placed it on my Raspberry pi, after installing some packages, the last one I had to so was Pandas_ta. I searched op documentary, I tried out some youtube video's. But it feels harder then it should. Does someone had a guide for me ?
Related
I am trying to install OpenCV in raspberry pi 3B but every time I try to install it gives error during compilation. I have been trying this for a long time and I don't know how to do it. I have followed mainly all the instruction given in these articles :
Install opencv 4 on raspberry pi
Install guide raspberry pi 3 raspbian jessie opencv 3
I had the same error a few weeks ago and for me it works when I just use
make -j
instead of
make -j4
-j4 simply means that the raspberry pi uses all for cpu cores instead of just one with make -j
Hope I could help and please write if that works for you as well ;)
Hi everyone,
I tried everything to install pyalsaaudio package on my Raspberry Pi Zero W
can anyone please help me with a guide to install it on my device ?
I see a lot of guides for Ubunto OS and i even tried them on my device but nothing worked for me.
Thanks in advance.
there is a adafruit tutorial which works just perfect.
You have to install some libraries before, reboot at a certain point for them to make efect and last you enable the module.
Here is the link https://learn.adafruit.com/adafruit-i2s-mems-microphone-breakout/raspberry-pi-wiring-and-test#
Hope it works!
I'm having some difficulties importing the module dht11 from the Adafruit library(https://github.com/adafruit/Adafruit_Python_DHT).
I'm using a raspberry pi3 model b, and have installed python 3.5. I downloaded the Adafruit and installed using
sudo python3 setup.py install
and I'm fairly certain that the installation went well since I connected my temp and humidity sensor and using
sudo python3 examples/AdafruitDHT.py 11 2
I get correct reading about temp and humidity, yet when I try to import the dht11 module (I'm using spyder as ide) I get the
'no module named dht11'.
I tried appending the directory in the sys.path but still get the same error.
Edit:
I tried both python 2 and 3, get the same error
Edit2:
I tried other IDE as well, but no one is working.
I opted to launch the script.py directly from terminal since this way it's working. If anyone has a solution, it would be greatly appreciated.
I'm trying to connect raspberry pi with MatLab. I use the toolbox within matlab to configure raspberry pi. It automatically connects through network however it also gives you OS within that setup procedure, you can't connect to raspberry pi without it. Although the system it gives is technically Raspbian Jessie it comes with limited package.
When it launches and I input dir into console it only shows files such as: satkin_ws install ros_indigo.sh install_ros_package.sh and ros_catkin_ws. No other folders or files are pre-loaded onto the system. I tried to install some packages for display manager such as gdm3 and lightdm but I still have a problem with loading desktop environment. Can someone give me suggestions on how to resolve this issue?
Alright after doing some research I found that the system installed by Matlab is Raspbian Jessie Lite which does not come with GUI/Desktop environment by default but you can install it you want. Here is the link to get you going:
https://www.raspberrypi.org/forums/viewtopic.php?f=66&t=133691
I need to set up a GUI that simply shows the output of Pocketsphinx on Raspberry Pi. I have installed Pocketsphinx and can run it from command line, but am not quite clear on how to set up the GUI. I have been using Python 2.7, and have seen online that others have tried importing it? Please help me figure this out.
Thanks,
There is pocketsphinx wrapper for python.